Ideally i want the amp to be less powerful than the sub so that i do not blow the sub. Do you think there is a safe way? You can use this diagram as a wiring guide for your sub. Would these items work well together?

How to Wire a Dual 4 Ohm Subwoofer in Parallel for a 2 Ohm Load 6 Steps

The truck box has a negative and positive coming out on the right and the subs in each box are a dual voice coil already parallel wired. If you want a question answered about a system, you should identify the gear by brand names and model numbers so we can get the right information to you. Is there a better way to wire them up without hurting anything or am I better off eliminating a sub? John, If the specs you quote are correct, you can safely connect that gear together. Can you help me out with a wiring diagram?

How to Wire a Dual 4 Ohm Subwoofer in Parallel for a 2 Ohm Load

Step 2 Cut and Prepare the Speaker Wire

Series Connections

Step 1 Gather the Necessary Materials and Prepare the Box

The radio works with the carscomputer to reset codes and other stuff. Why should an amplifier think it is better to have a heavier load? On that amp it has two speaker out puts.

Kenneth, I'd leave your subs wired the way they are. If you want left-right separation for your subs, two mono amps will work best. If you want a question answered about a system, you must identify the gear by brand names and model numbers so we can get the right information to you. Efren, It sounds like your amplifier is being so over-driven it's going into protection mode to save your subwoofer from destruction.

What would you suggest here? Basically I just want to know if its better to have an amp that matches the subs perfectly in power output or to have a bit of headroom. Ok so I've heard a lot of my buddies refer to you diagrams for wiring up subs and I've used them a few time to help.

My budget allows me to get a amp that puts out exactly w rms but I could get one that puts out w rms for not much difference in price. An amplifier itself has no ohms - it senses whatever load is attached to its output, and responds accordingly. At peak demand, this system would try to draw amperes from your batteries and alternator.

How to Wire a 4 Ohm Amp to a 2 Ohm Speaker

Four days after installation the subs blew up. The positive on the left side to the negative on the right side. If you want a question answered about your system, you should identify your equipment by brand names and model numbers. Is this a correctly powered setup? Johnny, If your receiver only has a pair of subwoofer outputs, the simplest way to feed all four of your amplifier's channels is to use a couple of Y-cords to split the two channels into four.

There is plenty of room and clearance. Believe they are watts a piece. Just wanted to know if this amp has enough to power these subwoofer without any damage to any of my equipment? In order to prevent blowing your replacements, online dating no you must understand about setting the amp's gain and other controls correctly. The best way to get a question answered about a system is to identify the gear by brand names and model numbers so we can get the right information to you.

A note about amplifiers
How to Wire a 4 Ohm Amp to a 2 Ohm Speaker

This is connecting the voice coils and wiring them in a parallel configuration. Push down on the first negative terminal and insert the stripped end of the second piece of black negative wire. Nic, Without knowing precisely what amp and subs you're referring to, we can't help you with advice.

How can you hook up a 2 ohm amplifier to a 4 ohm sub
  1. Here is the list of items that are used for this simple installation.
  2. If you want accurate answers to your questions, you must identify your gear.
  3. How do you add an amp and sub to a stock eclipse?
  4. Not knowing exactly which you have makes it impossible to give advice on how to wire them together.

Our customers were recording studios, nightclubs, and touring bands. Do you have any recommendations on amps? Then, big fish dating website push down on the first positive terminal and insert the stripped end of the blue positive wire.

How to hook up speakers correctly for proper impedance

Adding Poly-Fil simulates a larger box, which results in deeper bass. Or if either of those amps could even power those subs? With the above mentioned head unit, which setting should I use? Caleb, genes good You're definitely confusing issues by quoting max ratings which are meaningless.

How can you hook up a 2 ohm amplifier to a 4 ohm sub

The amplifier sees the same load on its outputs and the subwoofers receive the same amount of power. Not knowing exactly what amplifier or subwoofers you have make it impossible to give advice on how to wire them together. Fill the subwoofer box with Poly-Fil. What's the best way to wire them to get good bass? The amp may be a bit strong for those subs, but they'll be fine as long as you set the amp gain so no distortion ever plays.

If the box is already the right size and then you put in polyfill you run the risk of blowing the sub as it now sees a much larger box size. The rating on the amplifier is the least resistance it should have on its load. Bridging refers to combining adjacent amplifier channels together, like in the diagram, and doesn't apply to subs or speakers.

What kind of amplifier would be needed to hook up a stereo to a television? Which is the best way to hook them up to get more bass or do I need a bigger amp? Im trying to get my system planned out before I hook up all the gear.

Can a car amplifier be wired in a house to power subs? Then, take the other end of this piece and insert it into the second negative terminal. Good day, I am looking for some information for wiring my stereo system. Could you please direct me to the diagram to get the most performance out of this combination? Impedance is the amount of electrical resistance, or load, a sub puts up against an amplifier's output.

My guess is I need an amp. How would I safely and efficiently wire these together? How should i wire these for the best output?

No Diagram Available

It Still Runs

In this case speaker B is being ask to dissipate more watts than it is rated to do. They are the doubles tacked magnets. If so how should i wire it? How would you recommend wiring it all up if I have a sealed box that has a divider in the middle, with wiring terminals on the outside of the box?

Buck Pomerantz
  • Most popular dating site in malaysia
  • Dating my best friend but not in love
  • Dating no counter offer
  • Marriage not dating ep 14 synopsis
  • Ciao dating cafe
  • Dating online disabled
  • Marriage without dating sub thai ep 7